Contact Us
020-22852352
info@elecbao.com
No. 33, Baishahu Bei Jie, Junhe Town, Baiyun District, Guangzhou, China. Post Code: 510440
Led Controller
2.4G RF RGB led controller with remote, 3 ZONE
  • 2.4G RF RGB led controller with remote, 3 ZONE

2.4G RF RGB led controller with remote, 3 ZONE

Item No.: 971324
DC12~24V, 2.4G Grouped RF RGB led controller, 4A/ch, 3 channel, DC12V<144W, DC24V<288W, 3 group
INQUIRY
DC12~24V, 2.4G Grouped RF RGB led controller, 4A/ch, 3 channel, DC12V<144W, DC24V<288W, 3 ZONE

Product Description
This 2.4G 3 zone Touch Remote RGB controller is human touch type and key control type universal RGB controller. Adopting the most advance PWM control technology, can control all kinds of 3 channel (common anode) and 4 wires LED lights. Such as LED module, led strip, led control box, led source,etc. This controller is easy to connected with wires and very simple to use. It is with synchronous indicating light and power off memory function. User can choose different changing mode, adjust the speed and brightness,turn on/off by the remote controlling. User can get flash effect, strobe effect, fade effect etc according to their demand .

Technical Parameters
● Working temperature-20~55℃
● Supply voltageDC12V~24V
● Output3 Channel
● Connection modeCommon anode
● Controller sizeL85×W45×H23mm
● Net weight86g
● Static power consumption<1W
● Output current<4A/CH
● Output power12V:<144W24V:<288W
Direction for use:
Remote Function introduction
1Use the 2.4G frequency RF remote control, no need to make the remote direct to the controller, and the RF remote can control it across obstacles.
2In the open area remote control distance is about 30 meters.
3Adopt touch control remote, slightly touch the color wheel can switch the light color easily and smoothly
Operation method:
1Connect the load wire at first, following by the power wire; Please make sure no short circuit between connecting wire before you turn on the power;
2Only the ON button is effective in the OFF station, press the power button for the first time then controller will enter to the last mode before turn off the controller last time (memory off function).
3Press ON button to start, then press mode button      can switch the 9 modes as following
4When it is ring control status, press    button, it will go back to latest  mode.
5Hold the“+”“-”can quickly adjust the speed and brightness level.
Number Mode Adjustable state
1 3 colors jumping change

Brightness is not adjustable, speed is adjustable
2 3 Colors fade in and fade out
3 Seven color  jumping change
4 Seven color fade
5 White color fade in and fade out
6 Red color fade in and fade out+flash 3 times
7 Green color fade in and fade out+flash 3 times
8 Blue color fade in and fade out+flash 3 times
9 Auto-cycle mode













Match code and clean code Instruction
For a new combination, the remote have to match code with the receiver then it can be used normally. Before match code, switch on the power to check if the LED Controller, power supply and led light are connected correctly.
Match code: Switch off the power, then Switch on again (within 5 seconds)long press the “Group X(X=1,2,3)”Button for 2 seconds. the output led light will be quickly flash for 3 times, this means the remote is matched code with this receiver successfully, they can be used normally.
For example: there are A and B controller. Firstly, Switch on the power for A(within 5 seconds)long press “Group 1”button for 2 seconds, the output led light will be quickly flash. “Group 1” can control A controller.
Secondly, Switch on power for B(within 5 seconds)long press “Group2”button for 2 seconds, the output led light will be quickly flash, “Group 2” can control B controller
When long press Master OFF button, Both A and B will be turned off, then short press Master ON button, Both A and B will be turned on, A and B can be controlled in the same time. Well,if A is turned on and B is turned off , short press Master ON button, the A will be turned off, B will be turned ON
If need control A independently, press GROUP 1 firstly, then the touch ring can control A only. Similarly, for Group 2 and Group 3.
Remark:a remote control can operate 3 groups of controllers at the same time. each group of controllers can be composed of many controllers, such as 30 controller divided the 3 groups, then, each group control can remote 10 controllers, to achieve synchronously adjustable brightness effect.
Clean code:
If need change the Group combination, the link between remote and receiver can be cleaned. Then rebuild the link as required.
Code clean method
Switch on power for controller(within 5 seconds)long ress “GROUP X(X=1,2,3)”button for 2 seconds, the related led light will be quickly flash for 3 times, that means this group has been cleaned code. 
Remark: our factory default for set package is Group 1 linked to controller. User can build link according actual demand. One remote can be linked with countless controller, one controller only can be linked with 2 remotes.

Typical Application

Review


Air
Ben
Air
Air